Accelerating the decarbonization of carbonaceous gold ore by suspension oxidation roasting towards the improvement of gold leaching efficiency

Eliminating the gold preg-robbing effect of carbonaceous matter in carbonaceous gold ores is crucial for gold leaching. In this study, suspension oxidation roasting was proposed to accelerate the decarbonization of carbonaceous gold ore. The characteristics of oxidation reaction process and gas release were analyzed by TG-DTA-FTIR. The phase transformation and microstructure evolution of samples during roasting were analyzed by XRD, SEM and BET. The results show that the gold preg-robbing effect was eliminated after the gasification of carbonaceous matter, and the CaO generated by decomposition of carbonates can effectively capture the SO₂. After roasting for 75 min at 650 °C in a 20% O₂ atmosphere, the total carbon removal rate reached 99.42%, the distribution of exposed gold increased from 28.85% to 77.10% and the gold leaching efficiency increased from 4.55% to 84.83%. In addition, about 70% sulfur was mainly fixed in the roasted products in the form of sulfate. Therefore, the suspension oxidation roasting process is an efficient and clean pretreatment method for carbonaceous gold ores.     

Achieving fabrication of highly transparent Y2O3 ceramics via air pre-sintering by deionization treatment of suspension

An easy albeit quite effective deionization suspension treatment was adopted to alleviate the detrimental effects related to the hydrolysis of Y₂O₃ in an aqueous medium. Fabrication of highly transparent Y₂O₃ ceramics with a fine grain size via air pre-sintering and post–hot isostatic pressing (HIP) treatment without using any sintering additive was achieved using the treated suspensions. The hydrolysis issue of Y₂O₃ powder in an aqueous medium was effectively alleviated by using deionization treatment, and a well-dispersed suspension with a low concentration of dissolved Y³⁺ species was obtained. The dispersed suspensions were consolidated by the centrifugal casting method, and the green bodies derived from the suspension of 35.0 vol% solid loading showed an improved homogeneity with a relative density of 52.1%. Fully dense Y₂O₃ transparent ceramic with high transparency was obtained by pre-sintering consolidated green compacts at a low temperature of 1400°C for 16 h in air followed by a post-HIP treatment at 1550°C for 2 h under 200 MPa pressure. The sample had a fine average grain size of 690 nm. The in-line transmittance of the sample reached 83.3% and 81.8% at 1100 nm and 800 nm, respectively, very close to the theoretical values of Y₂O₃.     

Emerging Plasmonic Assemblies Triggered by DNA for Biomedical Applications

Plasmonic gold nanocrystal represents plasmonic metal nanomaterials, and has a variety of unique and beneficial properties, such as optical signal enhancement, catalytic activity, and photothermal properties tuned by local temperature, which are useful in physical, chemical, and biological applications. In addition, the inherent properties of predictable programmability, sequence specificity, and structural plasticity provide DNA nanostructures with precise controllability, spatial addressability, and targeting recognition, serving as ideal ligands to link or position building blocks during the self-assembly process. Self-assembly is a common technique for the organization of prefabricated and discrete nanoparticle blocks for the construction of extremely sophisticated nanocomposites. To this end, the integration of DNA nanotechnology with Au nanomaterials, followed by assembly of DNA-functionalized Au nanomaterials can form novel functional Au nanomaterials that are difficult to obtain through conventional methods. Here, recent progress in DNA-assembled Au nanostructures of various shapes is summarized, and their functions are discussed. The fabrication strategies that employ DNA for the self-assembly of Au nanostructures, including dimers, tetramers, satellites, nanochains, and other nanostructures with more complex geometric configurations are first described. Then, the characteristic optical properties and applications of biosensing, bioimaging, drug delivery, and therapy are discussed. Finally, the remaining challenges and prospects are elucidated.     

基于MOOC技术的在线金课建设策略

金课是对网络在线M O O C 教育的继承和发展，不仅注重对学生专业理论知识的讲解，更强调对学生高级思维意 识、知识转化为实践能力的培养，具有创新性、高阶性、挑战性等特征。围绕在线金课课程的建设，从课程教学情境、知识结构 体系、教学内容、交互模式等方面入手，进行网络化精品金课的组织与设计，满足广大学生群体多样化的专业课程学习需求。     

Easy access to pharmaceutically relevant heterocycles by catalytic reactions involving α-imino gold carbene intermediates

This review summarizes recent advances in the field of gold-catalyzed synthesis of pharmaceutically relevant aza-heterocycles via in situ generated α-imino gold carbene complexes as intermediates.     

福建某低品位金矿新型浸金剂浸金试验

福建某斑岩型金矿品位低、规模大,金主要以自然金形式存在,可见金的粒度较粗,为高效利用该低品位金矿,开展新型浸金剂金蝉全泥浸出试验和柱浸试验,结果表明：全泥浸出在磨矿细度为-0.074 mm占80%、矿浆浓度25%、加石灰调pH 值11.0左右、初始金蝉浓度为500 mg/L和过程中控制金蝉浓度不小于300 mg/L条件下浸出20 h,金的浸出率为93.43%,金蝉耗量为1.02 kg/t；柱浸在矿石粒度为-30 mm条件下喷淋浸出23天,金累计浸出率和金蝉累计耗量分别为86.54%和1.22 kg/t。     

云南镇源难处理金精矿工艺矿物学研究

利用X射线衍射、X射线荧光光谱（XRF）、X射线能谱分析（EDX）和矿物解离分析（MLA）等检测手段对云南镇源难处理金精矿的化学组成、矿物组成、硫化物特征以及金的分布情况进行了详细的工艺矿物学研究。结果显示：该金矿以硫化矿、碳酸盐和硅酸盐类矿物为主，含有3.18%的有机碳和2.37%的无机碳。通过金的诊断浸出发现96.16%的金被硫化物包裹，少量金以单体形式存在。通过对主要载金矿物黄铁矿、辉锑矿和毒砂的粒度、包裹及裸露情况进行分析，得出大部分硫化矿以解离单体的形式存在，少部分与其他矿物共生。根据MLA测试及金的诊断浸出，认为大部分金被硫化矿完全包裹，处理该矿石时应先进行硫化物包裹层的氧化处理，再进行金矿的浸出。     

Impact of Divalent Ions on Heavy Oil Recovery by in situ Emulsification

Many reservoir formation brines are characterized by high salinity and contain high concentrations of divalent ions such as calcium, magnesium, and potassium. These challenging conditions can render the surfactants ineffective during chemical flooding for enhanced heavy oil recovery. Various brine types can have an impact on the stability of emulsions generated with chemicals as chemicals have various resistant levels toward hard divalent ions and salinities. To investigate the impact of brine hardness on heavy oil-in-water emulsion stability, glass tube experiments, microscopic visualization and sandpack flooding experiments, and Hele-Shaw visualization experiments were conducted in this study under low-salinity/hard-brine, high-salinity/hard-brine conditions using commercial chemicals, which are designed for specific reservoir brine conditions. Recovery results demonstrated that complex colloidal solution introduced in the previous study with silica and Dodecyltrimethylammonium bromide (DTAB) along with screened chemicals from glass tube tests in this study can enhance heavy oil recovery significantly with an addition of low concentration of xanthan gum (Lee and Babadagli 2018). The results confirmed the robustness of the complex colloidal solution formula to enhance oil recovery with low concentration of polymer under any reservoir brine conditions. The study also demonstrates the potential of polymer as an emulsion stabilization additive for enhanced heavy oil recovery by in situ emulsion generation. Polymer effects seemed to be particularly dominant under the low-salinity conditions than high-salinity conditions.     

Robust Metallic Actuators Based on Nanoporous Gold Rapidly Dealloyed from Gold–Nickel Precursors

Dealloyed nanoporous gold (np-Au) has applications as oxygen reduction catalysis in Li-air batteries and fuel cells, or as actuators to convert electricity into mechanical energy. However, it faces the challenges of coarsening-induced structure instability, mechanical weakness due to low relative densities, and slow dealloying rates. Here, monolithic np-Au is dealloyed from a single-phase Au₂₅Ni₇₅ solid-solution at a one-order faster dealloying rate, ultra-low residual Ni content, and importantly, one-third more relative density than np-Au dealloyed from conventional Au₂₅Ag₇₅. The small atomic radius and low dealloying potential of the sacrificing element Ni are intrinsically beneficial to fast produce high relative density np-Au, as predicted by a general model for dealloying of binary alloys and validated by experiments. Stable, durable, and reversible actuation of np-Au takes place under cyclic potential triggering in alkaline and acidic electrolytes with negligible coarsening-induced strain-shift. The thermal and mechanical robustness of bulk np-Au is confirmed by two-order slower ligament coarsening rates during annealing at 300 °C and 45 MPa macroscopic yielding strength distinctive from the typical early onset of plastic yielding. This article opens a rich direction to achieve high relative density np-Au which is essential for porous network connectivity, mechanical strength, and nanostructure robustness for electrochemical functionality.     

Compact Quantum-Dot Microbeads with Sub-Nanometer Emission Linewidth

Fluorescent microbeads are widely used for applications in life sciences and medical diagnosis. The spectral contrast and sharpness of photoluminescence are critical in the utilities of microbeads for imaging and multiplexing. Here, microbeads capable of generating single-peak laser emission with a sub-nanometer linewidth are demonstrated. The microbeads are made of quantum dots that are tightly packed and crosslinked via ligand exchange for high optical gain and refractive index as well as material stability. Bright single-mode lasing with no photobleaching is achieved with particle diameters as small as 1.5 µm in the air. Sub-nm lasing emission is maintained even inside high-index surroundings, such as organic solvents and biological tissues. Feasibility of intracellular tagging and multi-color imaging in vivo is demonstrated.